Gifts Under $50

Bar end plugs (2)

Updated and more secure clothing clip for mounting CatEye safety lights.

Finish off that great road bar tape job with Origin-8's Rubber End Plugs. These plugs come in a variety of colors to dress up your rig and fit most handlebars.

Recon-E Light to Bosch motor unit connector cable.

A universal quick release mount that attaches to round-shaped drop and flat handlebars.

Recon-E Light to Shimano motor unit connector cable.

- Rack mount bracket only - Fits TL-L225 taillight

The NiteRider Tail Light Mount – Seatstay and Seatpost is our classic seatpost mount design that gives riders the option to mount their tail light to their seat stay, using the included seat stay clamp. System Compatibility - Sentinel - Solas - Sabre - CherryBomb - TL 5.0 SL

- Attaches to rear racks - Compatible with: Blinky 3,5,7 and Superflash - 25mm between each of the top horizontal holes (center to center) - Requires an "L bracket" that typically comes with a rear rack. If your rack is missing the L bracket, you can purchase Planet Bike's rack hardware pack

- Replacement aero mount for Numen light

Mounting bracket for MSW front White Bat Headlight. - Includes 1 front mounting bracket

Replacement bracket for Pico and Tigermoth lights. - Includes 1 front bracket, 1 rear bracket, and 2 mounting straps

- Mounts Beamer and Blaze 1/2W lights to a helmet - Compatible with Beamer 1, Beamer 3, Beamer 5, Blaze 1/2W and Blaze 2W Micro, Blaze 140 SL, Blaze 180 USB - Increased weight and length of Blaze 300, 500, and 650 USB lights may cause awkward mounting on helmet

Optional Accessory Rear rack Bracket for mounting most CatEye Taillights to rear racks with 50/80 mm spaced mounting holes.

SP-12 Flex-Tight Seatpost Bracket for most CatEye taillights

- Quick Strap mounts, adjusts or removes in seconds without tools - Fits 25.4-35mm handlebars - Compatible with Blazes, Beamers, 1200 and Super Spot

- Compatible with all Blaze headlights, Beamer 1/3/5, 1200, Dual Spot, and Bright Spot bike headlights - Fits 25.4 – 31.8mm handlebars

- Fits 25.4-31.8mm handlebars - Compatible with Blaze, Beamers, 1200, 5000x and Super Spot

Compatible with Shiner and Shiner Back lights - Rubber pad with loop straps to quickly mount and remove light for recharging - 50mm bolt spacing to fit most rear racks

The Portland Design Works Stayputnik tail light bracket has a UV-proof rubber strap to securely hold your tail light on nearly any size seat post. - Mounts in seconds and is compatible with every Portland Design Works tail light except Asteroid and Fenderbot. - UV proof rubber strap - Compatible with every PDW tail light except Asteroid and Fenderbot

Mount your tail light to the reflector tab on the back of a rear cargo rack with this Rack Bracket from Portland Design Works. - Compatible with all PDW rear lights except the Asteroid and Fenderbot - Horizontal holes are 50mm apart to fit European rack standards - Vertical holes are 18mm apart to fit most reflector mounts

SRAM's Handlebar End Plugs are just the thing for adding a fun, custom touch to your handlebar taping job. They feature SRAM's famous and stylish "Make the Leap" frog logo.

• Soft foam • w/End plugs • 125mm

- Compatible with Blinky 3,5,7, Superflashes, Turbo, Turbo Minis Superflash Micros and Blinky Safety rear light - Designed specifically for aero seat posts - Adjustable light angle - Easy on/easy off design makes for quick mounting and removal

- Compatible with seatpost diameter 20mm-36mm - Adjustable light angle - Easy on/easy off design makes for quick mounting and removal - Compatible with Blinky 3,5,7, Superflashes, Turbo, Turbo Minis, Superflash Micros and Blinky Safety rear light

- Simplistic safety light designed to be seen - Easy to install silicone strap attachment is compatible with 22.2-31.8mm bars - 3 modes including 1 steady and 2 flashing modes - Powered by 2 CR2032 batteries - Lumens: 6

SRAM Racing Grips offer a great grip for total control and come in several sizes to fit your front-end setup. These durable rubber grips have stylish logos stamped in them and are built to last and not slip.

Others out on the roads and paths will see you when Sunlite's TL-L340 Taillight is on your bike. It sports 3 bright LEDs, steady and flashing modes, and a long run time.

Dimension Classic Cruiser Grips available in black and white. - Flange: No - Grip Shift Specific: No - Length: 140mm - Lock On: No - Shape: Round - Weight: 104g

The NiteRider Tail Light Strap Mount allows for quick installation and fitment on to standard seat posts. It features a quick release tab that allows you to remove just your tail light, leaving the strap mount installed on the seat post; ideal for when you leave your bike unattended or when it's time for a recharge. System Compatibility - Sentinel - Solas - Sabre - CherryBomb - TL 5.0 SL Not compatible with omega 300 and sentry aero 260 tail lights.

Put it on your seatpost, put it on your seatstay, put it anywhere—Sunlite's Griplite goes everywhere. This powerful little light boasts two LEDs and runs for a whopping 100 hours! It has steady and two flashing modes, and is housed in a water-resistant body.

Yep, these are the same old-school grips from back in the day. Now you see them on skinny-barred messenger fixies from NYC to San Fran. Sunlite's Classic grips come in a rainbow of colors to match any scheme on any bike. The large pads provide fat cushion for your hands and the soft rubber gives you a slip-free grip.

Put it on your handlebars, put it on your fork leg, put it anywhere—Sunlite's Griplite goes everywhere! This powerful little light has 2 LEDs and runs for a whopping 100 hours! It has steady and flashing modes and is housed in a water-resistant body.

• 2 bright Nichia LEDs • Uses 2 CR 2032 lithium batteries (included) • 100 hour run time • 3 modes: 2 flashing and 1 steady • Water-resistant silicone body

Sunlite's Handlebar Tape boasts a diamond grip pattern. It offers a great feel on any handlebar and comes with two bar end plugs.

- Low profile, timeless small ribbed spiral grips - Soft rubber compound with closed ends - Length: 125mm

• 2 bright Red LEDs • Includes 2 (CR 2032) lithium batteries • 100 hour run time • 3 mode (2 flashing modes & steady mode) • Water resistant silicone body

Keep adhesives off your bike! This is the finishing tape included in our RCT Wrap Kits. If you remove the protective backing and feel the material it feels exactly the same on both sides. There are no adhesives! If you touch it to itself you have just a few seconds to peel it away before it starts to bond. It bonds to itself or to our silicone grips, but not to your bike or to your components. No more cleanups. No more nasty glue stuck all over your bike or products. BENEFITS: ESI Silicone Tape has some of the same benefits as our grips. It is heat resistant, made in the USA, and long-lasting. Not to mention it's military-grade! - Easy to Install - Hassle Free - Self-Bonding - No Residue - No Adhesives - UV Resistant NO CLEAN UP: The best part of our tape is when you are done with it, cut it off, and throw it away. No Clean up needed! USES: There are countless uses for our silicone tape. One awesome use is it makes a great chainstay protector. Also, wrap it under mounts to keep your lights, cameras, GPS, etc. from rotating and scratching your bars. Basically, anything you use adhesive/electrical tape on you can now use ESI Silicone Tape instead without the mess. With 10ft in a roll, you can get numerous chain stay protectors and custom tape jobs. Some other great uses include: - Tool Handles - Finishing Tape - Protecting Wear Points - And Much More The possibilities are endless!

Experience what so many cyclists are using, the Logo grip. It satisfies many riders providing durability. This is a great grip for those with medium-sized hands. Single compound grip includes push in plugs. - Length: 130 mm - Weight (with plugs): 109 grams - Diameter: 31.75 mm

- Best seller - Shock Absorbing Design - Ridged Turbo Shape - Fits 7/8" Bars - Style: with Flange - Length: 110mm

- Smaller grips for smaller hands in a comfortable and fun dinosaur print - 97mm length

Smaller grips for smaller hands in a comfortable and fun dolphin print - 97mm in length

- Smaller grips for smaller hands in a comfortable and fun flower print pattern - 97mm length

Sunlite's HL-K100 Headlight is a great light at a great price. It sports a super-bright Krypton bulb housed in a tough, water-resistant body so it's perfect for commuting year round. A no-tools-required quick-release handlebar mount is included, too.

Be seen with CatEye's Omni 3 Taillight, which uses Omni Directional Technology for 360 degrees of visibility. Three super-bright LEDs light up in three different modes so you can customize the pattern and get run times up to 200 hours. Plus, CatEye's tool-free mount makes installation a breeze.

Optional Accessory Saddle Rail Mount Bracket for most CatEye taillights.

Simple mushroom style design made of Krayton rubber. - Flangeless slim mushroom design - Bar ends included

Dan Paley signature grips: Dan Paley is really fussy when it comes to grips, not too fat, not too thin, not too squishy, the list goes on. The Dan Paley Slims however are just right. - Flangeless Dan Paley zigzag design - Krayton rubber - Bar ends included

Bontrager's SSR Grips are made from a dual compound: the hard inner core eliminates slippage on the bars, the soft outer layer provides great grip and all-day comfort in any condition.

Dimension Cork Grips are the classic style grip for cruisers or mountain bikes. - Flange: Yes - Grip Shift Specific: No - Length: 125mm - Lock On: No - Shape: Round - Weight: 26g

Lizard Skins bar end grips are 165mm in length, cut to fit neoprene.

The NiteRider Adjustable Angle Tail Light Strap Mount was specifically designed for our flagship tail light, the Sentinel. It allows you to fine-tune the mounting angle of the light to display the projected Laser Lanes even and parallel on the ground. It's an easy on and off non-slip tail light mount that also features a grooved contact pad that makes this the 'go to' mount for riders using aero seat posts. System Compatibility - Sentinel - Solas - Sabre - CherryBomb

All of our head light mounts deliver rock solid mounting but for those that demand the most rigid set up, the NiteRider Lumina Handlebar Clamp Mount is here to deliver a high degree of performance and stability. Fits a max bar diameter of 35mm. SYSTEM COMPATIBILITY - Lumina Series - MiNewt Cordless Series - Mako Series WARRANTY - This NiteRider accessory is backed by NiteRider’s lifetime warranty that covers any defects in mechanical components (housings, covers, mounts and fasteners)

The NiteRider Lumina Handlebar Strap Mount offers a wide variety of handlebar size fitments and remains rock solid while riding through rough terrain. It’s easy to install and, like all NiteRider mounts, features a quick release tab for when it’s time to recharge or leave your bike unattended. System Compatibility: - Lumina Series - Mako Series - MiNewt Cordless Series

The NiteRider Tail Light Rack Mount gives you the option to mount your tail light directly onto your rack-ready/-equipped bike via this rack mount accessory. System Compatibility - Sentinel - Solas - Sabre - CherryBomb - TL 5.0 SL

Broc Raiford signature grips feature a comfortable ribbed design and smooth ends for improved wear resistance. - 160mm lenght - Par Ends Included

Enjoy classic style and feel with Origin-8's Dual Classic Grips. These dual compound grips are made from soft Kraton rubber.

Make sure you have excellent rear visibility at night with the Blinky 3. This sweet taillight aims 3 bright LEDs directionally to provide visibility from up to a mile away. Its soft-touch power switch accesses flashing or steady modes for up to 100 hours of run time on the 2 AAA batteries (included). And, it includes seatpost and seatstay mounts.

CatEye's Center Fork Bracket helps clear your handlebars by positioning your favorite CatEye headlight (sold separately) in front of your bike's head tube.

Giant's Ally Quarter Socks use quick-drying, breathable TransTextura fabric with a mesh top and seamless heel.