Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Parts & Accessories

$29.99
Keeps corrosive sweat from reaching your frame. - Cell phone pouch included.
$24.99
The Saris Leveling Block keeps your bike level with your trainer. - Adds stability to your training ride. - For use with any rear wheel-mounted trainer. - Raises front bicycle tire 1.1 inches (2.8 cm) off the ground
$44.99
The E-Thru Trainer Axle allows the use of a mountain bike in a Tacx trainer. These axles are only suitable for Tacx classic trainers.
$59.99
TRAINER THRU AXLE ADAPTER FOR SARIS TRAINERS WHAT'S INCLUDED: - Thru axle - Washers - Endcaps with bolts - The 148x12mm adapters also come with a shorter bolt action slider tube. TRAINER COMPATIBILITY The Saris Trainer Thru Axle Adapter is designed for indoor use on Saris trainers only and should not be ridden outdoors. Compatible with current basic trainers. Not compatible with CycleOps PowerSync trainers. Contact us with trainer compatibility questions. BIKE COMPATIBILITY Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please reach out to your local bike shop or the bicycle manufacturer directly. Both 148x12 Thru Axle Adapters are compatible for both 142 and 148mm bikes. 148x12 Thru Axle Adapter, 1.5 Thread Pitch (9733T) works for: - 148 x 12mm - 142 x 12mm - 1.5 thread pitch
$54.00
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
$49.99
Connect your PC to CycleOps VirtualTraining.
$15.00
Giant's Chopping Block lifts your front wheel so it's even with your rear wheel while on a trainer. It's compatible with 26-inch and 700c wheels and has a stable, anti-skid base.
$99.99
The Elite Smart Sterzo riser block allows steering up to 34 deg while riding your rear wheel trainer while using ANT and Bluetooth communication protocol, interacts with compatible apps to give you the most realistic indoor ride. It’s rotating pivot features a practical automatic return system for you to easily get the handlebar back to its original position. Compatible with tires up to 56mm wide
$8.79
Replacement straps for Sunlite FlatForm II pedals - Strap size: 340 x 55mm
$29.99
- Includes clutch knob and L-bolt - Basic Trainer Clutch Knob is compatible with any Wind, Mag, Mag+, Magneto or Fluid trainer that already uses L-bolt - Magnus Clutch Knob should only be used with Magnus Smart Trainer - Watch our video to learn more
$359.99
Trainer Mission Control Every training room needs a control center, and the TD1 is more than equipped for the job. Featuring built-in power strip with 2 AC and 2 USB outlets, this indoor trainer desk was designed to keep everything you need charged, organized and close at hand. Its roomy 12" x 20" table top is made from laminated birch for easy clean up, and is supported by stainless, corrosion-resistant steel sourced from America’s heartland. And as part of the Saris trainer eco-system, the TD1 is a perfect complement to the MP1 trainer platform. After just one ride with a dedicated trainer desk, you’ll ask yourself how you ever rode indoors without one. - Stay Charged: built-in power strip keeps training necessities nearby and powered up. - Pick Your Height: adjustable for wide range of bikes and training configurations. - Easy Cleaning: laminated birch wood top makes for easy clean-up post-ride. - Steamlined Look: built-in cable management and stainless steel hardware are both functional and eye-pleasing. - Enhanced Experience: a great addition to indoor training. Specs - Base: 13-inches wide x 36-inches Depth - Desk Top: : 12-inches Width x 20-inches Depth - Adjustable Desk Height from Floor: 40- to 55-inches - Materials: Laminated birch table top supported by a steel frame, featuring stainless steel and corrosion-resistant hardware - Cord Length: 6- foot AC cord - Built-in power strip with 2 AC and 2 USB outlets - Built-in cord retention clips for easy cable management and a clean look.
$39.99
This height-adjustable front wheel support can simulate both flat terrain and slopes perfectly - Unique design with 5 levels lets you adjust the height of your front wheel to simulate hill climbs up to 6% - Anti-slip rubber feet eliminate handlebar vibrations - Internal design that guarantees maximum wheel stability - Suitable for both road and MTB - You can attach to the trainer frame when not in use for easy transport and storage
$69.99
- Adapter for Tacx Direct Drive trainer - 01 is compatible with 142 x 12mm and 148 x 12mm - 02 is compatible with 135 x 10mm - 03 is compatible with 135 x 12mm (w/5 mm spacer included with every Tacx Direct Drive trainer), 142 x 12mm and 148 x 12mm - 04 The thru axle adapter kit is for bikes with a 12 mm thru axle. The axle adapter is required to couple the rear stay with the thru axle mount on a Tacx NEO or FLUX Smart trainer.
$39.99
Adjust resistance on Mag trainer without leaving the saddle. - Quick Release mounting system fits most stems. - For use with the Mag bike trainer only
$29.79
• Plastic riser block allows the position of front wheel at one of two heights
$12.99
Keep your handlebar organized and your devices secure with the LW-STD (22.2/25.4/28.6mm) from Minoura. - Alloy clamp for mounting your own device on handlebar or stem - Lightweight and rustproof aluminum construction - Hex wrench required for instillation and removal - Clamp body has (1) M5 Thread hold in center - 22.2 mm-28.6 mm diameter range
$37.99
The TPH-1 Tablet Grip from Minoura is the ultimate tablet holder for indoor training. Fitting a diameter between 28mm and 35mm, this stand will fit most bicycles. - Perfect accessory to use with LiveTraining Apps, The Sufferfest videos, or other media - SM clamp easily mounts or dismounts from the handlebar or tube - Spring-loaded clamp system is simple to use and securely holds your device in place - Holds from a 7.9 to 9.7 inch screen with 360 degree rotation system - Can mount to your repair stand so you can easily reference the Internet when working on your bike
$79.99
Protects your floor from sweat and bike grime. Product Features: - Protects your floor from sweat and bike grime. - Keeps your trainer from "walking" during intense workouts. - Durable construction absorbs vibration and noise. - Training mat measures 65 x 36 inches. - Black PVC foam gives the training mat superior sound absorption. - Resistant to moisture, and easy to clean with soap and water when necessary.
$70.00
The Giant Indoor Trainer Mat is the perfect noise-reducing floor protection for indoor training. - Rubberized material for easy rinse off after your workout - ‘Pebbled’ surface, anti-skid and scratch-resistant material protects flooring while working out - Extra-large 3’ x 6’ (91.5cm x 183cm) size covers entire workout area, prevents perspiration from getting on carpets or wood floors - Comes rolled-up in draw-string, mesh carry bag with shoulder strap
$129.99
Everything you need for the best indoor trainer experience possible. - Can be used across a wide range of trainer setups. - Includes Trainer Mat, Climbing Block and Saris towel.
$59.99
Adapts a thru axle hub bike for a Saris bike trainer. - Trainer Thru Axle Adapter For Saris Trainers - Thread pitch: 1.00 & 1.75 What's Included: - Thru axle - Washers - Endcaps with bolts Trainer Compatibility The Saris Trainer Thru Axle Adapter is designed for indoor use on Saris trainers only and should not be ridden outdoors. Compatible with current basic trainers. Not compatible with CycleOps PowerSync trainers. Contact us with trainer compatibility questions. Bike Compatibility Many bike manufacturers do not publish thread pitch or hub spacing online. If you are unclear as to what type of thru axle your bike uses, please contact us.
$29.99
The Skyliner is a front wheel support for use with Tacx classic trainers. It raises and supports the front wheel for a natural cycling position and increased stability. It also serves as a handle to carry the trainer.
$56.99
• 35.5-inches x 79-inches • Black
Page 1 of 1